[Author Index]
[Date Index]
[Thread Index]
[Date Prev][Date Next][Thread Prev][Thread Next]
Fw: Gas Leak!!!!
David,
I forgot to mention the following - but you are probably aware of it anyway:
there is a seal behind the plate. If you are going to loosen all 14 bolts
the fuel will spill out.
Cheers
Thomas
- -----Ursprüngliche Nachricht-----
Von: Thomas Maxhofer <Thomas.Maxhofer@xxxxxxxxxxxx>
An: <ST@xxxxxxxxxxxxxx>
Gesendet: Donnerstag, 6. April 2000 09:56
Betreff: Re: Gas Leak!!!!
> Hi David,
>
> I´m sorry to hear about this trouble. I just had a look into my ST/RS shop
> manual. Funny enough - there are two different torque values for the same
> bolts (there is a total of 14 bolts holding the plate):
>
> 5 Nm according to the respective picture
> 6 Nm according to the text section
>
> It´s not a big difference anyway. Just make sure you use the same value
for
> all bolts. The shop manual writes in bolded letters: DO NOT OVERTIGHTEN
> THESE BOLTS! This is because the nuts are embedded in the tank and could
be
> pulled out by overtightening the bolts. Hopefully this is not what has
> happened to your tank!
>
> I hope you can fix the problem soon and easily!
>
> Greetings
>
> Thomas
>
>
> -----Ursprüngliche Nachricht-----
> Von: Kelley & David <kdgaske@xxxxxxxxx>
> An: Sprint RS <RS@xxxxxxxxxxxxxx>
> Gesendet: Donnerstag, 6. April 2000 00:36
> Betreff: Gas Leak!!!!
>
>
> > Hello All,
> > Hoping you can help me. My RS has a fuel leak. Not a leak in the
> > since it is dumping its contents on the ground, but the fumes are over
> > whelming. The fumes were strong enough that they seeped into my house.
> > Some more history. While in for its 500 mile service they tightened the
> > fuel pump mounting plate (the large gold plate where the fuel lines go
> into
> > the tank.) They also straightened a kink in a fuel line that has a
> petcock
> > in it. I know you are supposed to keep your pet cocks on a leash, but
> this
> > one had a kink in it, or was it just plain kinky. Anyways.. I now
would
> > like to fix this my self. I can see there is a minute gap around the
fuel
> > pump mounting plate, I am guessing this is my culprit. Can someone go
out
> > and look at theirs and see if there is a small gap or is it flush
mounted.
> > Even better can someone post the torque values for this plate (it uses
> some
> > small (maybe 8mm) bolts, and there are about 10 or so of them)? Also,
> does
> > anyone know where this "petcock" is at, as I want to see if there is a
> kink
> > again. Since I would like to try and wrap this up tonight so I can ride
> > tomorrow I am posting my phone number (please no heavy breathers).
> >
> > Thanks, Thanks and some more thanks,
> >
> > David "Lost Dawg" Gaske
> > '00 Sprint RS (yellow)
> > Fredericksburg, Va. USA
> > 540-891-0089
>
>
* * * * * * * * * * * * * * * * * * *
The ST/RS Mailing list is sponsored by Jack Lilley Ltd.
http://www.TriumphNet.com/st/lilley for more info
http://www.TriumphNet.com/st for ST, RS and Mailing List info
=-=-=-= Next Message =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=